# Transformer kVA Sizing & Fault Current Calculator

> Size a three-phase distribution transformer in kVA from plant load, demand factor, power factor and growth margin, plus HV/LV currents and secondary 3-phase short-circuit current Isc.

Canonical: https://engitech.in/transformer-kva-short-circuit-calculator/ | Published: 2026-11-18 | Updated: 2026-11-18

Size a three-phase distribution transformer in kVA from plant load, demand factor, power factor and growth margin, plus HV/LV currents and secondary 3-phase short-circuit current Isc.

Free engineering tool Formula, worked example and FAQs below · results update as you type

Results

**Required transformer rating**

—

**Primary full-load current (HV)**

—

A

**Secondary full-load current (LV)**

—

A

**Secondary 3-phase fault current (Isc)**

—

Results are engineering estimates for preliminary design. Verify critical values with codes, vendor data or a qualified engineer.

## Formula used

Required **kVA** = (kW × Demand ÷ cos φ) × (1 + Margin). Full-load current **I** = kVA × 1000 ÷ (√3 × V).

Bolted 3-phase secondary fault current (infinite primary bus): **Isc** = ILV ÷ (%Z / 100).

## How to use this calculator

1. Enter total connected kW, expected demand factor and average power factor.
2. Add spare capacity margin (typically 20–25 %) and pick the next standard kVA frame (e.g. 500, 750, 1000, 1600 kVA).
3. Enter HV/LV voltages and %Z to check LV breaker interrupting kA rating.

## Worked example

A 600 kW plant (80 % demand, 0.85 PF, 25 % margin) requires **705.9 kVA** (select a standard **750 or 1000 kVA** 11 kV / 415 V unit). LV FLA = **982 A**; at 5 % impedance, **Isc = 19.64 kA**.

## Frequently asked questions

**How does %Z affect transformer short-circuit current?**

Lower %Z reduces voltage regulation dip during motor starting, but raises secondary bolted fault current (Isc = I_FLA / %Z), requiring higher-kA MCCB/ACB switchgear.

**What load percentage gives maximum transformer efficiency?**

Most distribution transformers achieve peak efficiency around 50–70 % of rated kVA, where no-load core losses equal load-dependent copper (I²R) losses.

**Should harmonic loads (VFDs, rectifiers) derate a transformer?**

Yes. Non-linear VFD and UPS loads add eddy-current heating; specify a K-factor (K-4 or K-13) transformer or derate a standard unit by 15–25 %.

## More free engineering tools

[**Power Factor Correction (kVAR) Calculator**Capacitor kVAR needed to improve power factor, with kVA and current before and after correction.](https://engitech.in/power-factor-correction-calculator/)[**Cable Voltage Drop Calculator (IEC 60228)**Voltage drop, percentage drop and power loss for copper and aluminium LV cables using IEC 60228 conductor resistance corrected to operating temperature.](https://engitech.in/cable-voltage-drop-calculator/)[**Motor Running Cost & Energy Calculator**Electrical input power, annual energy use and running cost of a motor from its rating, load, efficiency and operating hours.](https://engitech.in/motor-running-cost-calculator/)[**PT100 RTD & Thermocouple Resistance / mV Calculator**Convert process temperature to IEC 60751 PT100/PT1000 resistance (Ω) or Type K/J thermocouple millivolts, plus 4–20 mA transmitter loop output and Class A/B tolerance.](https://engitech.in/pt100-rtd-thermocouple-calculator/)[**Electric Motor FLA, Starter & Overload Sizing Calculator**Calculate full-load current (FLA), starting peak current by starter type (DOL, Star-Delta, Soft-Starter, VFD), thermal overload setting and minimum contactor rating.](https://engitech.in/electric-motor-fla-starter-calculator/)[**Motor Torque, Power & Current Calculator**Convert motor power and speed to shaft torque, or torque to power, and estimate full-load current for three-phase and single-phase motors.](https://engitech.in/motor-torque-power-calculator/)

[All calculators →](https://engitech.in/engineering-tools/)
