# Pipe Schedule Dimensions, ID & Weight Calculator

> Calculate pipe inside diameter, empty weight per metre, total dry weight, water-filled weight and internal volume for ASME/IS process piping.

Canonical: https://engitech.in/pipe-schedule-dimensions-weight-calculator/ | Published: 2026-11-18 | Updated: 2026-11-18

Calculate pipe inside diameter, empty weight per metre, total dry weight, water-filled weight and internal volume for ASME/IS process piping.

Free engineering tool Formula, worked example and FAQs below · results update as you type

Results

**Inside diameter (ID)**

—

**Empty weight per unit length**

—

**Total empty pipe weight**

—

**Water-filled total weight**

—

**Internal volume**

—

Results are engineering estimates for preliminary design. Verify critical values with codes, vendor data or a qualified engineer.

## Formula used

Inside diameter **ID** = OD − 2 × t. Steel cross-section Am = π × (OD² − ID²) ÷ 4. Empty weight per metre **w** = Am × ρ.

Internal volume **V** = (π × ID² ÷ 4) × L. Hydrotest / water-filled weight adds V × 1000 kg.

## How to use this calculator

1. Enter pipe OD and wall thickness from ASME B36.10M / B36.19M.
2. Enter total run length and pipe alloy density.
3. Use the water-filled weight for pipe rack and hanger load design, and internal volume for flushing or hydrotest water planning.

## Worked example

A 6 m length of 4" Sch 40 carbon steel pipe (OD 114.3 mm, wall 6.02 mm, ρ = 7850 kg/m³) has ID = **102.26 mm**, empty mass = **16.07 kg/m** (96.4 kg total) and water-filled weight = **145.7 kg**.

## Frequently asked questions

**Why does pipe outside diameter stay fixed across schedules?**

So standard fittings, flanges and pipe clamps fit the same NPS size regardless of pressure rating. Increasing the schedule thickens the wall inward and reduces the inside diameter.

**Should pipe supports be sized for empty or water-filled weight?**

Always size supports for at least the water-filled weight plus insulation, even on gas or steam lines, because the line is filled with water during hydrostatic pressure testing.

**What is the difference between Schedule 40 and Schedule 40S?**

For NPS 12 and smaller, ASME B36.10M Sch 40 (carbon steel) and ASME B36.19M Sch 40S (stainless steel) have identical wall thicknesses; above NPS 12 they differ.

## More free engineering tools

[**Pump Power & Motor Size Calculator**Hydraulic power, shaft power and recommended motor rating for centrifugal pumps from flow, head, density and efficiency.](https://engitech.in/pump-power-calculator/)[**Fan & Blower Power Calculator with Fan Laws**Air power, shaft power and motor size for centrifugal fans and blowers, plus fan-law results for a new speed.](https://engitech.in/fan-blower-power-calculator/)[**Pipe Pressure Drop Calculator (Darcy–Weisbach)**Velocity, Reynolds number, friction factor and pressure drop for liquids and gases in pipes, including fittings.](https://engitech.in/pipe-pressure-drop-calculator/)[**Pump NPSH Available Calculator**Net positive suction head available (NPSHa) for a pump, compared with the pump’s NPSHr to check cavitation margin.](https://engitech.in/npsh-calculator/)[**Pipe Flow Velocity & Reynolds Number Calculator**Flow velocity, Reynolds number and flow regime for a liquid or gas in a pipe, plus the pipe bore needed for a target velocity.](https://engitech.in/pipe-velocity-reynolds-calculator/)[**Pump Affinity Laws Calculator (Speed & Impeller Trim)**New flow, head and power of a centrifugal pump after a change in speed or impeller diameter, using the affinity laws.](https://engitech.in/pump-affinity-laws-calculator/)

[All calculators →](https://engitech.in/engineering-tools/)
