# Dust Collection System Design: Hoods, Ducts, Filters and Fans

> Design dust collection from hood to fan. Capture velocity, duct sizing, bag filter area and fan power worked example plus a commissioning checklist.

Canonical: https://engitech.in/dust-collection-system-design/ | Published: 2026-11-20 | Updated: 2026-11-20 | Author: Jignesh S Panchal

**Short answer:** a dust collection system works when four things are right: the hood captures the dust at the source, the duct keeps it moving, the filter is sized for the airflow, and the fan can overcome the total resistance. Most poor systems fail on the first two, not on the filter that gets all the attention.

I meet a lot of plant owners who bought a bag filter and still have dust on the floor. When we walk the line together, the filter is rarely the problem. The hood is too far from the source, a branch duct was added without checking the fan, or the filter bags are blinded because the pulse cleaning was never set up. This guide follows the order I use when I look at a plant.

## 1. Capture at the source

Dust is easiest to control where it is made. A hood or enclosure close to the source needs far less air than a large opening far away, because capture velocity falls rapidly with distance. Practical rules:

- Enclose the source as much as possible. A small opening with air drawn in is better than an open hood.
- Place the hood where the dust naturally travels, not against it.
- Do not fight cross-draughts from doors and fans.
- Typical capture velocities at the point of dust release range from about 0.5 m/s for quiet release to 2.5 m/s or more for high-speed processes. The ACGIH *Industrial Ventilation Manual* gives accepted figures by process.

## 2. Duct design

The duct must carry the dust without letting it settle, and without wearing through at the bends. For most industrial dusts, design transport velocities of about 18 to 23 m/s are common, with heavier or wet dust needing more. Too low and dust drops out and blocks the pipe. Too high and you waste fan power and wear the elbows.

- Use smooth, long-radius bends. A sharp elbow can have several times the resistance of a good one.
- Join branches at an angle of 30 degrees or less, entering from the side or top.
- Provide clean-out doors at low points and after bends.
- Use a balanced layout, or fit blast gates, so air goes where it is needed.

## 3. Choosing the collector

| Collector | Good for | Limits |
| --- | --- | --- |
| Cyclone | Coarse, heavy dust; pre-cleaner ahead of a filter | Poor on fine dust below a few microns |
| Pulse-jet bag filter | Fine dust, high efficiency; see [bag filters guide](https://engitech.in/bag-filters/) | Needs compressed air; wrong media blinds |
| Cartridge collector | Fine, dry dust in compact space | Not for sticky or heavy loads |
| Wet scrubber | Sticky, hot or explosive dusts and gases; see [air scrubbers](https://engitech.in/air-scrubbers-guide/) | Water treatment, corrosion |
| Electrostatic precipitator | Large volumes of hot gas, very fine particles; see [ESP guide](https://engitech.in/electrostatic-precipitators-guide-benefits-applications/) | High capital cost, dust resistivity |

### Worked example: sizing a bag filter, duct and fan

A process needs 12,000 m³/h of air to control dust.

- **Filter area.** With an air-to-cloth ratio of 1.2 m/min: 12,000 / 60 = 200 m³/min, then 200 / 1.2 = **about 167 m² of cloth**. Fine, sticky or hot dust needs a lower ratio, and coarse free-flowing dust can take a higher one. Check the manufacturer’s data for your dust. The [bag filter sizing calculator](https://engitech.in/bag-filter-sizing-calculator/) will do this for you.
- **Main duct.** 12,000 m³/h = 3.33 m³/s. At 20 m/s, area = 3.33 / 20 = 0.167 m², which is a diameter of about 0.46 m. A 450 mm duct is the nearest practical size.
- **Fan power.** If total system resistance is 2,000 Pa (hood, ducts, bends, filter and outlet) and the fan efficiency is 65%: power = 3.33 × 2,000 / 0.65 = 10.3 kW at the shaft. Add a margin for the motor and for filter loading. The [fan power calculator](https://engitech.in/fan-blower-power-calculator/) covers this step.

Filters pick up resistance as dust cakes on the bags, so always size the fan for the dirty-filter pressure drop, not the clean one.

## 4. Filter media and cleaning

Choose the media for temperature, chemistry and moisture: polyester for general use up to about 130 °C, acrylic and PPS for different chemicals, glass or PTFE-membrane for severe conditions. Pulse cleaning should be triggered by differential pressure rather than a fixed timer. Cleaning too often wears bags, and too rarely lets the cake build. Keep compressed air dry and at the right pressure, or the bags will blind.

## 5. Fire and explosion

If the dust is combustible, which includes flour, sugar, many plastics, wood, coal and metal powders, explosion protection is part of the design, not an extra. Options include explosion venting, suppression, isolation valves in the ducts, spark detection, and locating the collector outside the building. The right choice depends on test results for the dust. NFPA 652 and NFPA 660 are widely used references, and local rules also apply. Never skip the dust test to save time.

## 6. Discharge and housekeeping

Use a rotary airlock or double-dump valve so the filter stays sealed while collected dust leaves. Check the hopper for bridging and the airlock for wear. The collected dust has to go somewhere: bags, bins, or back to the process. Include that in the plan.

## What I notice in plants

- Systems are extended year after year with no fan check. The last machine added gets weak suction.
- Operators prop blast gates open or cut holes in ducts to “get more air” from their own point, starving everything else.
- Differential pressure gauges are fitted and never read. A gauge on the board turns a problem you see in six months into one you see this week.
- The cheapest way to improve capture is often to move the hood closer or add a skirt, not to buy a bigger fan.

## Commissioning checklist

1. Measure airflow at each hood and compare with design.
2. Check fan rotation, motor current and speed.
3. Record filter differential pressure clean and during operation.
4. Confirm pulse timing and compressed air pressure.
5. Check the discharge valve and the dust containers.
6. Take a smoke test at hoods to see capture working.

## Go deeper: the full guide series

These guides cover each stage of a dust and air system, from the hood to the stack.

- Hood and Duct Design for Dust Capture
- Duct Velocity and Pressure Drop in Dust Systems
- Baghouse Troubleshooting: High Pressure Drop and Short Bag Life
- Choosing a Filter Bag Fabric
- Pulse-Jet Cleaning Settings: Pressure, Pulse Length and Interval
- Baghouse, ESP or Wet Scrubber: A Decision Table
- Cyclone Efficiency and Cut Size Explained
- Choosing an ID Fan for a Dust Collector
- Dust Explosion Protection: Venting, Isolation and Suppression
- Stack Emission Monitoring in India: What Gets Measured and How Often
- Wet Scrubber Design and Maintenance
- Welding Fume Extraction: Source Capture or Room Ventilation
- Industrial Ventilation: Air Changes or Heat Load
- Cleanroom Classes: ISO 14644 in Plain Terms
- Activated Carbon Filters for VOC and Odour
- Fan Noise and Silencers in Industrial Plants
- HEPA or ULPA: Which Filter Do You Need
- Duct Leakage: Testing and Cost of Leaks
- Baghouse Commissioning Checklist

**Free tools for this topic:** [Bag filter sizing calculator](https://engitech.in/bag-filter-sizing-calculator/) · [all free engineering tools](https://engitech.in/engineering-tools/)

## Frequently asked questions

### What is air-to-cloth ratio?

It is the airflow divided by the filter cloth area, expressed in metres per minute. A lower ratio means a larger filter for the same airflow, and longer bag life on difficult dust.

### Why does my filter pressure drop keep rising?

Common causes are blinded bags from moisture or oil, weak or mistimed pulse cleaning, wrong media, or an airflow higher than design.

### Can I add another machine to an existing system?

Only after checking duct velocity, filter loading and fan capacity. Adding without a check usually reduces suction at every hood.

### Do I need a cyclone before the bag filter?

If the dust is coarse or the load is heavy, yes. A pre-separator reduces load and wear on the bags.

### How long do filter bags last?

Anywhere from under a year to several years depending on dust, temperature and cleaning. Trend the pressure drop and emissions to decide, not the calendar.

*General engineering information. Dust systems can involve fire, explosion and health hazards. Have the design reviewed by a qualified specialist.*

## Sources and further reading

For standards, data and independent guidance on this topic, see [NFPA](https://www.nfpa.org/) (combustible dust and fire safety standards), [US Chemical Safety Board](https://www.csb.gov/) (dust explosion investigation reports), [IECEx](https://www.iecex.com/) (hazardous area equipment certification) and [ACGIH](https://www.acgih.org/) (the Industrial Ventilation Manual and exposure limits). Always check the current edition and your site conditions before applying any figure.
