# Steam Boiler Efficiency & Fuel Consumption Calculator

> Calculate direct steam boiler thermal efficiency, steam-to-fuel evaporation ratio, thermal duty \(MW\) and fuel heat input.

Canonical: https://engitech.in/boiler-efficiency-fuel-consumption-calculator/ | Published: 2026-11-18 | Updated: 2026-11-18

Calculate direct steam boiler thermal efficiency, steam-to-fuel evaporation ratio, thermal duty (MW) and fuel heat input.

Free engineering tool Formula, worked example and FAQs below · results update as you type

Results

**Direct boiler efficiency**

—

%

**Evaporation ratio (steam / fuel)**

—

kg/kg

**Boiler thermal output**

—

**Fuel heat input**

—

Results are engineering estimates for preliminary design. Verify critical values with codes, vendor data or a qualified engineer.

## Formula used

Feedwater enthalpy hf ≈ 4.186 × Tfw [kJ/kg]. Direct efficiency **η** = [ṁs × (hg − hf)] ÷ [ṁf × GCV] × 100 %.

Evaporation ratio = ṁs ÷ ṁf [kg steam per kg fuel].

## How to use this calculator

1. Enter measured steam flow and enthalpy from the steam table at boiler pressure.
2. Enter feedwater inlet temperature (after economizer if fitted).
3. Enter fuel GCV from lab test or supplier spec and measured fuel flow.
4. Track evaporation ratio daily to spot scaling, excess air or fouled heat-transfer tubes.

## Worked example

Producing 5,000 kg/h of 10 bar g steam (2778 kJ/kg) from 85 °C feedwater using 380 kg/h of furnace oil (GCV 42,000 kJ/kg) gives **75.9 %** efficiency and an evaporation ratio of **13.16 kg/kg**.

## Frequently asked questions

**What is the difference between direct and indirect boiler efficiency?**

Direct efficiency divides measured steam heat output by fuel heat input. Indirect efficiency measures stack gas, blowdown, radiation and unburnt losses and subtracts them from 100 % — it is more accurate when steam or fuel meters drift.

**How much fuel does raising feedwater temperature by 6 °C save?**

Every 6 °C rise in feedwater temperature via condensate return or an economizer saves roughly 1 % of boiler fuel consumption.

**Why is GCV efficiency lower than NCV efficiency?**

GCV (Higher Heating Value) includes latent heat of water vapour formed during combustion; because flue gas leaves above dew point, GCV-based efficiency is 5–10 % lower than NCV-based efficiency.

## More free engineering tools

[**Heat Exchanger LMTD & Area Calculator**Heat duty, log mean temperature difference and required heat-transfer area for counter-flow and parallel-flow exchangers.](https://engitech.in/heat-exchanger-lmtd-calculator/)[**Industrial Dryer Evaporation, Heat & Fuel Calculator**Water evaporation, product output, heat load and fuel or steam consumption for spray, rotary, flash, fluid-bed and paddle dryers.](https://engitech.in/dryer-heat-load-calculator/)[**Steam Consumption Calculator for Process Heating**Steam flow needed to heat a liquid continuously or in batches, using saturated-steam latent heat at your supply pressure.](https://engitech.in/steam-consumption-calculator/)[**Chiller Cooling Load & TR Calculator**Process cooling load in kW, kcal/h and tons of refrigeration (TR) from chilled-water flow and temperature difference, with chiller sizing margin.](https://engitech.in/chiller-tonnage-calculator/)[**Dew Point, Humidity & Wet-Bulb Calculator**Dew point, wet-bulb temperature, humidity ratio, enthalpy and air density from dry-bulb temperature and relative humidity.](https://engitech.in/dew-point-humidity-calculator/)[**Heating Time & Energy Calculator**Energy and time needed to heat a liquid or solid batch to a set temperature with a heater of known power.](https://engitech.in/heating-time-energy-calculator/)

[All calculators →](https://engitech.in/engineering-tools/)
