# 4–20 mA Scaling Calculator, PLC Raw Count Converter & Loop Troubleshooting

> Scale 4–20 mA loops to engineering units and Siemens or Allen-Bradley PLC raw counts, 250 Ω resistor voltage, NAMUR NE43 faults, and 5-point table.

Canonical: https://engitech.in/4-20ma-scaling-formula-calculator/ | Published: 2026-11-20 | Updated: 2026-11-20

Convert 4–20 mA, LRV/URV engineering values, and Siemens/Allen-Bradley PLC raw counts with 250-ohm 1–5V check, NAMUR NE43 status, and 5-point table.

Input Mode

Loop Current (mA)

LRV (4 mA / 0%)

URV (20 mA / 100%)

Engineering Unit

PLC Analog Card Family

Scaled Value**—***—*

Loop Current**—***—*

PLC Raw Count**—***—*

250 Ω Resistor Drop**—***1.00–5.00 V DC range*

NAMUR NE43: Normal Measurement Band (4.0–20.0 mA)

### 5-Point Loop Calibration Table (0% / 25% / 50% / 75% / 100%)

| Span % | Loop mA | 1–5 V (@ 250 Ω) | Engineering Value | PLC Raw Count |
| --- | --- | --- | --- | --- |

**EngiTech — engitech.in**4–20 mA Scaling Calculator, PLC Raw Count Converter & Loop Troubleshooting

**Embed this free tool on your website or blog**

Free to embed on engineering blogs, university guides, and plant wikis (zero login required).

2-wire 4–20 mA series loop: current stays immune to cable voltage drop until supply headroom collapses.

## The 5-Minute 250-Ohm Bench Trick & Headroom Math

Value = LRV + ((I_mA - 4) / 16) × (URV - LRV) | V_250 = I_mA × 0.250

Never break a live process loop with an ammeter if you do not have to—blowing your multimeter mA fuse drops the plant transmitter offline. Instead, wire or measure across the 250 Ω precision resistor at the terminal block in **VDC mode**: 1.000 V = 4 mA, 3.000 V = 12 mA, 5.000 V = 20 mA.

Always verify loop power headroom when adding isolators or long runs: most 2-wire transmitters need 12 V minimum at terminals, plus 5 V across a 250 Ω AI card, plus cable loop resistance (check wire Ω/km in our [AWG Cable & Voltage Drop Calculator](https://engitech.in/awg-to-mm2-cable-size-voltage-drop-calculator/)).

## 0 mA vs 3.8 mA & Related Loop Tools

**0.0 mA** means a broken wire, loose terminal, or blown loop fuse. **3.6–3.8 mA (or 21.0+ mA)** per NAMUR NE43 means the transmitter electronics are alive and reporting a sensor burnout (like an open [PT100 RTD](https://engitech.in/pt100-rtd-resistance-table-iec-60751-chart/)). Driving a motor speed reference? Compare analog feedback alarms on the [VFD Fault Code Troubleshooter](https://engitech.in/vfd-fault-code-troubleshooter/).

## Frequently Asked Questions

**What is the standard linear scaling formula for a 4–20 mA loop?**

Value = LRV + ((I_mA - 4) / 16) x (URV - LRV). Conversely, I_mA = 4 + 16 x ((Value - LRV) / (URV - LRV)). For a 0-10 bar transmitter, 12 mA is exactly 50% of span = 5.0 bar.

**What PLC raw integer counts represent 4 mA and 20 mA on Siemens vs Allen-Bradley?**

Siemens S7-1200 / S7-1500 AI cards map 4-20 mA to 0-27648 (27649..32511 is over-range). Allen-Bradley ControlLogix 1756 / CompactLogix in Engineering Units or 4000-20000 mode maps 4 mA to 4000 and 20 mA to 20000.

**How do you troubleshoot a 4–20 mA transmitter with a 250-ohm resistor and multimeter?**

Wire a precision 250-ohm resistor in series or measure across the PLC input resistor with a voltmeter: 4 mA reads 1.000 VDC, 12 mA reads 3.000 VDC, and 20 mA reads 5.000 VDC without breaking the loop.

**What is the difference between 0 mA and NAMUR NE43 3.6 mA / 21 mA?**

Zero mA means an open wire, blown loop fuse, or dead 24V power supply. Under NAMUR NE43, a healthy smart transmitter drives <= 3.6 mA or >= 21.0 mA intentionally to tell the PLC that the sensing element itself failed.

![Jignesh S Panchal](https://engitech.in/wp-content/uploads/2026/11/jignesh-s-panchal-author.jpg)

Technical Editorial Author Verified Editor

## Jignesh S Panchal

Founder — Jaadu Digital & Musafir Infotech · 9+ Years in Industrial B2B

Jignesh S Panchal is the founder of Jaadu Digital and Musafir Infotech, and the publisher behind EngiTech. With over 9 years of hands-on experience in industrial marketing and B2B growth, he works closely with machinery OEMs, process equipment manufacturers, and industrial service providers across thermal processing, fluid handling, automation, packaging, and plant reliability. Combining deep practical knowledge of industrial manufacturing with how technical buyers actually evaluate equipment, he built EngiTech to give plant engineers and procurement teams reliable sizing tools, fault diagnostics, and verified B2B supplier discovery.

[LinkedIn](https://www.linkedin.com/in/jignesh-s-panchal/) [All Guides by Author →](https://engitech.in/author/jignesh-panchal/) [Editorial standards](https://engitech.in/editorial-standards-and-corrections/)
